• <center id="o6owq"></center>
    <rt id="o6owq"><acronym id="o6owq"></acronym></rt>
    <table id="o6owq"><tr id="o6owq"></tr></table>
  • <bdo id="o6owq"><tbody id="o6owq"></tbody></bdo>
    <rt id="o6owq"><acronym id="o6owq"></acronym></rt>
    <rt id="o6owq"><acronym id="o6owq"></acronym></rt>
    <li id="o6owq"><dl id="o6owq"></dl></li>
  • 網站首頁技術中心 > CD-800 Dicing Machine               Instruction
    產品目錄
    CD-800 Dicing Machine               Instruction
    更新時間:2013-07-29 點擊量:3959

    This type of machine is specialized in vegetable and cormcutting. It is easily operating for woman. It is also the necessary facility for restaurants and second processing factories. Instantaneous ability is above 15 people. This machine will let you have satisfied feeling.

     

    A.   Processing material

        Potatoes, carrots, melons, bamboos, onions, apples, vegetables and so on.

     

    B. Processing dimension:

    (standard)

                   H                 10. 15. 20mm cubes or bars.

    L              T            (special dimension)

                                 3-20mm cubes or bars.

     

    C. Capacity

    15/mm cubes;    1000kg/hr

     

    D.   Voltage

    3 phase / 415V, 50Hz / 4P / 0.75KW

    (each countries has different voltage connection)

    E.   Machine dimension & weight

    L 800×W 700×H 1260mm

     

    F. Cutting work outline

        Connecting “ON” switch, add little water when machine is running and put suitable amount of material to the machine. (Material diameter under 8/cm). Leaf blade will turn over the material to the fixed thickness of the place of flate cutter. And crosscut cutter will cut the bars into cubes and flow down to the machine after round cutter cuts material into bars. Easily operate, and processing material is clean and delicacy.

     

     

     

     

     

     

     

     

     

     

     

    G. Voltage connection

        Power: 3 phase / 415V / 4P / 0.75KW. Connect power cord (red, black, white) when use the machine. Then connect (green) line to insurance after that start to operating.

     B

     

     

     

     

     

                   A

     

    (1) The power line A connected to power supply. (Attention the    motor shift)

    (Attention 4 power lines, green for the grounding line.)

    (2) Water pipeline will be connected B, then the installation is completed.

     

     

     

    H.   Installing location

        Consider whether the water drains unimpededly or not when install the machine.

     

    I.   Watch out the machine running

        Make sure there are no foreign objects on the entrance of the machine and inside of the leaf blade after connecting voltage to avoid the cutter broken while the machine running. Make sure the direction of leaf blade is correct, rith circum gyratoin (clock-wise).

     

    J. Method of adjusting thickness of flate cutting

    The standard allocation method as follows: (if cut cube is formed by three Cutter)

    (1) The first knife (cutting thickness): Plane broadswords Z.     (Adjustable by cutting thickness)

    (2)   The second knife (cutting width): Circular knife Group Y.

      5mmP (space): 5mm

     10mmP (space): 10mm

     15mmP (space): 15mm

     20mmP (space): 20mm

     

    (3)   The third knife (cut length): transverse plane knife Group.

    5mm uses 15 knife group

    10mm uses 8 knife group

    15mm uses 6 knife group

    20mm uses 4 knife group

     

    K.   Method of adjusting aluminum fence

    Aluminum fence feeds material to crosscut cutter when round cutter cuts the material. This is why the sharp place of aluminum fence has to get close to the cushion of gap of round cutter or the dimension of aluminum fence marks on the bottom right side.

     

    L. Round cutter discharging

    Round cutter dimension drawing

    Round cutter dimension

     

     

    Standard (mm)

    P: 10

    P: 15

    P: 20

    Special (mm)

    P: 3-20

    (1) Avert black screw of fixed eccentric axis.

    (2) Pull down the fixed bolt of round cutter eccentric axis. Then round cutter can be discharged.

    (3) Fix the u-shape spanner on the round cutter set, then loosen sexangular on the round cutter axis (two sides of 24m/m spanner), then it can be taken out.

     

     

     

    M. Crosscut cutter discharge

    Crosscut cubes round piece

    5m/m uses 21 pieces

    10m/m uses 8 pieces

    15m/m uses 6 pieces

    20m/m uses 4 pieces

    (1) Fix u-shape spanner on the fixed crosscut cutter set when discharge crosscut cutter. Then loosen sexangular screw (24m/m spanner), then it can be taken out.

     

    N. Daily cleansing

        Clean the machine after finish the jobs. Run the machine while operating, then wash it by flush water to clean the leavings.

    O.   Standard by-products:

    Spanner         10, 19, 24………….3

    Screwdriver (-), (+)……….……………2

    U-shape spanner                 1 PCS

    Lubricant oil                    1

    Tool box                       1 box

    成人久久久观看免费毛片| 久久久久亚洲精品影视| 久久精品国产精品亚洲艾草网美妙| 日本国产精品久久| 国产一区二区三区久久精品| 久久久久无码国产精品一区 | 国产精久久一区二区三区| 精品久久久久久久| 久久精品午夜一区二区福利| 国产精品久久久久久久小说 | 久久久久国产精品麻豆AR影院| 久久人人爽人人爽人人片AV超碰 | 精品国产婷婷久久久| 久久精品a一国产成人免费网站 | 国产精品99久久99久久久动漫| 久久久久久国产精品无码超碰| 久久亚洲精品视频| 久久躁狠狠躁夜夜AV| 久久96国产精品久久久| 国产精品久久久久网站| 五月丁香综合激情六月久久| selao久久国产精品| 亚洲国产欧洲综合997久久| 久久国产精品成人免费| 久久国产午夜精品一区二区三区| 爱做久久久久久久久久| 漂亮人妻被黑人久久精品| 亚洲国产精品成人AV无码久久综合影院| 91久久打屁股调教网站| 亚洲级αV无码毛片久久精品 | 中文字幕日本人妻久久久免费 | 精品中文字幕久久久久久| 国产精品久久久久久久久软件 | 国产精品久久久久国产精品| 久久精品免费一区二区喷潮 | 久久一区二区三区精华液使用方法 | 久久99精品久久久久婷婷| 亚洲综合婷婷久久| 伊人久久大香线焦综合四虎| 久久久久国产成人精品| 久久99精品久久|